Commercial Indoor Motion Sensor for SCW Shield - 74CIM
Usually ships the same business day if ordered before 2PM EST.
UL, IC, and FCC Listed for Commercial Insurance
Detects
Motion in a Commercial Building
40 Foot Range at 85 degrees
Where should I place motion sensors?
When would I use motion sensors, glass break sensors, vs. windows open sensors?
Actions
Siren, App Alerts, and Pro Monitoring when Armed and in Away Mode.
It is more secure and you will have fewer false positives if you use door and window sensors.
Battery
Averages 3 years


No Problem
Whether you plan to DIY install or want us to do it for you, we're as flexible as you need.
Get a Custom Quote for Equipment or Installation
UL, IC, and FCC Listed for Commercial Insurance
Detects
Motion in a Commercial Building
40 Foot Range at 85 degrees
Where should I place motion sensors?
When would I use motion sensors, glass break sensors, vs. windows open sensors?
Actions
Siren, App Alerts, and Pro Monitoring when Armed and in Away Mode.
It is more secure and you will have fewer false positives if you use door and window sensors.
Battery
Averages 3 years

Designed for commercial applications
85° detection range with 78 distinct detection zones
Range up to 40 feet
Selectable pulse count 2 or 4
4.53 x 2.44 x 1.97 inches
Commercial Indoor Motion Sensor for SCW Shield
Physical Specifications |
|
Housing Body Dimensions
|
4.53 x 2.44 x 1.97 inches (115 x 62 x 50 mm)
|
Weight with Battery
|
3.9oz (110.6 g)
|
Mounting Fastener
|
(2) #5 screws, (1) #8 screw, (1) square nut installed in unit, (1) #4 screw (All provided)
|
Environmental Specifications |
|
Operating Temperature
|
32°F to 120°F (0°C to 49°C)
|
Maximum Humidity
|
85% non-condensing relative humidity
|
Sensor Specifications |
|
Frequency
|
433.92MHz
|
Replacement Battery
|
One Panasonic CR123A Lithium Battery
|
Nominal Battery Life
|
3 years (assuming 720 trips/day), 7 years (assuming 240 trips/day)
|
Battery Voltage
|
3.0 VDC (Nominal), 2.2 VDC (Low)
|
Battery Voltage
|
21 mA (Maximum), 4.7 uA (Standby), 30 mA (Max in walk test)
|
Detection Range
|
Up to 40 Feet (12 m)
|
Detectable Speed
|
1 to 5 feet per second (0.3 to 1.5 meters per second)
|
Transmission Indicators
|
Motion, Cover Tamper, Wall Tamper, Low Battery, Supervision
|
Certifications |
|
Certifications
|
UL639, ULC-S306-03, ETL, FCC, IC
|
How to Pair
You only have to do this when ordering a separate sensor to add to a system. We will normally pair all your sensors when making your initial purchase.
Enroll by entering the serial number into the security panel. Alternatively, the sensor can be enrolled by placing the panel into enrollment mode, and then pulling the battery tab or tampering the device.
Installation Instructions
Install by screwing two #5 screws through the unit’s mounting knockouts. Use 2 of the 3 mounting knockouts in the center of the unit’s back to mount on a flat wall, or use 2 of the 4 corner knockouts to mount the unit in the corner of a room. Mount the sensor 5ft to 8 ft (1.5m-2.4m) high. Screw the #8 screw through the wall tamper knockout into the wall, ensuring that the wall tamper screw is attached to something solid. Tighten all screws until snug. Enroll the sensor using the instructions above. Close the cover and conduct a walk test. After testing, take the unit out of walk test mode and close the cover again. Finally, finish threading the white #4 screw until it is snug.
Mounting Tips
• Avoid direct sunlight
• Avoid facing directly to AC or heating vents
• Avoid vapor or high humidity
• Avoid curtains, screens, etc. from blocking detection
• Do not install outdoors
• Mounting height 5ft-8ft (1.5m-2.4m)